Q80bd-j61bt11n manual

Mitsubishi Electric 13J Manuals. Mitsubishi Electric Controller 13J Safety manuallines 80 pages. Mitsubishi Electric 13JY93 Manuals. Mitsubishi Electric a2 Series Manuals. Mitsubishi Electric Controller a2 Series Programming manual pages. Mitsubishi Electric E Manuals. Mitsubishi Electric ET Manuals. Mitsubishi Electric Got Manuals. Mitsubishi Electric C80 Series Manuals. Mitsubishi Electric E80 Series Manuals.

Mitsubishi Electric F Manuals. Mitsubishi Electric FR-A Mitsubishi Electric Apricot Manuals. Mitsubishi Electric Desktop Apricot Owner's handbook manual pages. Mitsubishi Electric apricot ft series Manuals. Mitsubishi Electric Desktop apricot ft series Owner's handbook manual 78 pages. Mitsubishi Electric meiki series Manuals. Mitsubishi Electric Engine meiki series Instruction manual 34 pages.

Mitsubishi Electric WD Manuals. Mitsubishi Electric Ecodan Manuals. Mitsubishi Electric C70 Manuals. Item Description 1 Channel No. Select the channel for setting the Target. Enter the logical station number to be set or modified. The following table shows each test can be selected or not. The parameter setting check list and the station information setting check list in Appendix can be used for the setting.

In data link: Normal data link is being performed. Remote device station station No. Page Page The following describes communications in the remote net Ver. Page RWr0 8. Page In this example, a system consisting of a master station and one intelligent device station AJ65BT-R2 as shown below is used. Refer to Section The shaded areas indicate the devices that are actually used. Master station station No. The data link is being L RUN executed normally.

Page With the sample program, initialization, transmission and reception are available. For error codes which are not listed in this section, refer to the following manuals.

If the corresponding error could not be found, check the cause by following the procedure shown below. The utility screen is not displayed properly. Or update the Windows operating system. Check the installation and uninstallation precautions. Refer to Section 7. Enable the creation of 8. Screen Instruction This screen appears when user account control is enabled. Click "Allow" or the Yes button.

Click the Yes button. This screen may be displayed a couple of times. The message is displayed when. NET Framework 3. NET 2. When an error occurs in the user program, take the action shown below. The following table shows the error messages that are displayed in event viewer. Event ID Error message Corrective action Item Corrective action The board or driver is not installed. Is the driver name of the board not displayed on the Device Manager screen?

Item Corrective action Is the board installed properly? Does the board operate on other personal computer? Status Error Cause It presents a list of check items and procedures for possible problems. Description of problem Check item Check procedure Is data written to the correct address of the remote Check the user program. Is data read from the correct address of remote Check the user program. Is data read from the correct address of the Check the user program.

Set the station When the block data assurance per station setting is enabled, the CC-Link Ver. Inform the following conditions and situations when inquiring the problems. Two words 32points are used per station. Four words are used per station. When a size is less than 1 word, it is rounded up and 1 is stored.

Local station Station No. The reading and writing of data are performed using transient transmission. When 1 station is occupied, 2, 4 or 8 words 32, 64 or points are used. When 1 station is occupied, any of 4 to 32 words are used.

When the standby master station is controlling the data link, availability is basically identical to that of the master station. When the standby master station is operating as a local station, availability is identical to that of a local station. Indicates the execution result of temporary error invalid station Temporary error SW SW Line status 0: Normal 1: Data link cannot be performed disconnected Indicates the occurrence status of a transient transmission error.

SW 0: No transient transmission error The following table shows the update timings of the link special registers. Link special register Data update timing Link special register Data update timing Updated individually regardless of the SB. Appendix 3. Page Appendix 3. Use it as a guide. Refer to the User's Manual for the intelligent device module to be used. POINT The own station access processing time by the md function varies depending on the performance of the personal computer, load status and other factors.

The processing time varies depending on the performance of the personal computer, load status, and other factors. Has error occurred? Error code is checked. Does the Retry processing error require retry processing? Wait processing Normal processing is executed. Error handling is executed.

For details other than those shown below, refer to Chapter 3. Page Appendix 5. For details of the functions, refer to Chapter 4. Appendix 6. Page Appendix 6. Page Appendix 7. Download directory. Catalog Download. Manual Download. Control axis: maximum 8 axes. Greater flexibility.